TM 9-2320-280-20-3
B-3. EXPLANATION OF COLUMNS IN THE MAC, SECTION II
i. Repair. The application of maintenance services, including fault location/troubleshooting,
removal/installation, and disassembly/assembly procedures, and maintenance actions to identify troubles
and restore serviceability to an item by correcting specific damage, fault, malfunction, or failure in a part,
subassembly, module (component or assembly), end item, or system.
j. Overhaul. That maintenance effort (service/action) prescribed to restore an item to a completely
serviceable/operational condition as required by maintenance standards in appropriate technical
publications (i.e., DMWR). Overhaul is normally the highest degree of maintenance performed by the Army.
Overhaul does not normally return an item to like-new condition.
k. Rebuild. Consists of those services/actions necessary for the restoration of unserviceable equipment to
a like-new condition in accordance with original manufacturing standards. Rebuild is the highest degree of
materiel maintenance applied to Army equipment. The rebuild operation includes the act of returning to
zero those age measurements (hours/ miles, etc.) considered in classifying Army equipment/components.
a. Column (1)-Group Number. Column 1 lists functional group code numbers, the purpose of which is
to identify maintenance significant components, assemblies, subassemblies, and modules with the next
higher assembly.
b. Column (2)-Component/Assembly. Column 2 contains the names of components, assemblies,
subassemblies, and modules for which maintenance is authorized.
c. Column (3)-Maintenance Function. Column 3 lists the functions to be performed on the item
listed in Column 2. (For detailed explanation of these functions, see para. B-2.)
d. Column (4)-Maintenance Category. Column 4 specifies, by the listing of a work time figure in the
appropriate subcolumn(s), the category of maintenance authorized to perform the function listed in Column
3. This figure represents the active time required to perform that maintenance function at the indicated
category of maintenance. If the number of complexity of the tasks within the listed maintenance function
vary at different maintenance categories, appropriate work time figures will be shown for each category. The
work time figure represents the average time required to restore an item (assembly, subassembly,
component, module, end item, or system) to a serviceable condition under typical field operating conditions.
This time includes preparation time (including any necessary disassembly/assembly time)
troubleshooting/fault location time, and quality assurance/quality control time in addition to the time
required to perform the specific tasks identified for the maintenance functions authorized in the
maintenance allocation chart. The symbol designations for the various maintenance categories are as
follows:
NOTE
When a complete replace or repair task performed at higher
level maintenance includes lower level maintenance tasks
(equipment condition/follow-on tasks), the lower level work
time figures in the MAC must be added to the higher level
work time shown in the MAC to determine the total time to
accomplish that maintenance function.
C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operator or crew
O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unit maintenance
F. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Support maintenance
H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Support maintenance
D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Depot maintenance
e. Column (5)-Tools and Equipment. Column 5 specifies, by code, those common tool sets (not
individual tools) and special tools, TMDE, and support equipment required to perform the designated
function.
f. Column (6)-Remarks. This column shall, when applicable, contain a letter code, in alphabetic
order, which shall be keyed to the remarks contained in Section IV.
B-2